Melting pot mod

  • 706 Views
  • Last Post 16 April 2017
Tooweels posted this 16 January 2017

Poor boy addition to my Lee pot that's dripped a bit from day one and also makes for easy adjustment to pouring speed, the spanner sits tightly on top of two nuts locked together a lot easier than fiddling with a screwdriver, when in operation the spanners about 180 degrees from currant position, Im sure others may have done the same but if not here it is

Attached Files

  • Liked by
  • onondaga
  • delmarskid
Order By: Standard | Newest | Votes
onondaga posted this 17 January 2017

That looks great and adds weight directly to the valve pin instead of adding weight to the linkage assembly like other innovations I've seen including Lee's own new metal knob for the op handle. Bravo! But you gotta notice right in the picture how off level your pot was where ever it sat when it cooled.   I wouldn't grab that wrench with the pot hot and a bare hand either. Include that in your safety label!

 

Gary

Attached Files

Duane Mellenbruch posted this 17 January 2017

I prefer to have the base of the pot at this angle to make it easy to scrape drips or spills off the front of the base.  If the spill gets under the base, it does not just brush away.   As to the wrench handle, some will actually cast wearing gloves as part of their PPE. 

Attached Files

OU812 posted this 17 January 2017

Flow rate is very important. When the lead level in pot drops the flow rate must be increased by turning wrench (opening) a few degrees to get a more consistent flow rate. I need to add some type of T handle to my RCBS for a more accurate reading.

Attached Files

vmwilson posted this 20 January 2017

Not exactly what I presently use on my 10# but had a 1/4” x 3/4” long bolt brazed on my valve rod.  Now has a tapped piece of 1-1/4” steel rod on there with 1/4” bolts tapped in to make a tee.  Add's weight in the bargain.  Don't know if something similar would work on a 20# though.

Mike

Attached Files

JeffinNZ posted this 20 January 2017

I plugged the pouring spout and bought a ladle. 

Cheers from New Zealand

Attached Files

  • Liked by
  • Maven
Maven posted this 20 January 2017

"I plugged the pouring spout and bought a ladle.”   ... JeffinNZ 

Exactly!!!

Attached Files

David Reiss posted this 20 January 2017

Both of my 10# Lees sit a little unlevel. Never knew it was a problem though . Maybe a little technical tests would tell if it makes a difference, but my suspicions are it would lead to more speculation than fact. 

David Reiss - NRA Life Member & PSC Range Member Retired Police Firearms Instructor/Armorer
-Services: Wars Fought, Uprisings Quelled, Bars Emptied, Revolutions Started, Tigers Tamed, Assassinations Plotted, Women Seduced, Governments Run, Gun Appraisals, Lost Treasure Found.
- Also deal in: Land, Banjos, Nails, Firearms, Manure, Fly Swatters, Used Cars, Whisky, Racing Forms, Rare Antiquities, Lead, Used Keyboard Keys, Good Dogs, Pith Helmets & Zulu Headdresses. .

Attached Files

BigMan54 posted this 03 April 2017

Very inventive.  If I ever find my old LEE pot in my garage mess I'd like to try this. How did you bend the wrench ?

I put a 1” x 10” piece of 1/4” plywood under the rear of all my pot bases before I clamp them down. just seems to make the flow from the spout a bit better for me. 

Long time Caster/Reloader, Getting back into it after almost 10yrs. Life Member NRA 40+yrs, Life S.A.S.S. #375. Does this mean a description of me as a fumble-fingered knuckle-draggin' baboon. I also drool in my sleep. I firmly believe that true happiness is a warm gun. Did I mention how much I HATE auto-correct on this blasted tablet.

Attached Files

Tooweels posted this 10 April 2017

 Hi Bigman

                 In my previous occupation I met a few well actually a lot of so called Knuckle draggers but don't believe any of them thought about casting bullets ! I just put that wrench in the vice and applied some love with a propane torch and bent it with the leather glove I use for casting, too easy was over and done in 5 minutes and has been in its present home for a minimum of 5 gals of 357  bullets don't think ill ever take it off it works so well

Attached Files

4570sharps posted this 16 April 2017

I like it!

Attached Files

Close