What 30 cal bullet do you hunt with

  • 17K Views
  • Last Post 20 September 2011
Scott Merchant posted this 22 November 2006

Let me start by saying that I hunt Deer with cast bullets. I was wondering what moulds and velocity are being using in the 30 cal to take Deer with. I would also like to know how far the deer went, What the wound channel was like, and did it leave a good blood trail. Other information such as alloy, and how far the shot was would be good.                                                           Thanks Scott

Attached Files

Order By: Standard | Newest | Votes
Duplex posted this 22 November 2006

31141 for years until I went to .38, .45 & .50 caliber in cartridges.  It always exited the body, I would wait for my favorite shot with hard cast (which was with the near leg forward and shooting through the lung area and the off shoulder.  Never lost a deer.

Ooooops, almost forgot... cast wheel weights (old mix) and my own lube of peanut oil and beeswax.

Attached Files

Scott Merchant posted this 22 November 2006

Duplex          The Lyman 311041 is one of my favorite bullets for hunting along with the Saeco 305. On the 30 cal bullets I believe the flat meplat will deliver a quicker kill, and a better wound channel. I run my hunting loads around 1900fps. I have never had a bullet stay in a deer yet. They go down fairly quick.                                                Scott

Attached Files

Mnshooter posted this 29 November 2006

I shot a medium deer with a Lee 200 grain 30 cal out of a .303 British at about 2000 fps.  The alloy was similar to electrotype, about 3% antimony and 3% tin which is softer than #2.  Shot was at 70 yards. I did not need to track as the deer went down in sight after about 25 yards.  The bullet went through diagonally behind shoulder and out midsection with a large exit hole that did not hit a rib on entrance.  The backtrail demonstrated an excellant blood trail had I needed it.  I am also interested in feedback on 30 cal, 8mm and 35 cal rifle loads for deer.

Attached Files

Ed Harris posted this 08 December 2006

Hunting deer with .30 cal. cast bullets you end up in most cases with ballistics like the .32-40 or .30-30, maybe closer to the .303 Savage or .30-40 Krag if you can use the heavier bullets and get decent velocity.

I've killed maybe a dozen deer with cast loads in .30 cals., and they will do the job OK if you place shots well, but you should use a bullet with as large a meplat as will feed, keep the alloy hardness about BHN13 or less, and the velocity 1700 f.p.s. or more.  Within 50 yards they work really well, but the farthest shots I've taken with cast, around 150, required some trailing, as they didn't go down right away.  Not alot of meat destruction at 1800 f.p.s.

If you need a harder bullet which remains ductile so that it will expand and stay together, you can do some tricks with the metallurgy.   I use ONE part of wheelweights to SEVEN parts of plumber's lead and then heat treat the bullets at 475 degs. F for six hours to ensure all the antimony is in solution, then immediately water quench, put the bullets in a ziplock bag and move them to the freezer to cold soak for 14 days.  They will harden to about 16-18 BHN to enable decent velocity, but they will expand and hold together at velocities from 1800-2000 f.p.s.

The flatnosed version of the bullet shown in the photo is our preferred hunting bullet.  Veral Smith made the original “beer can meplat” bullet for Nick Croyle.  This leaves a nice exit hole like a .44 Mag. SWC and lets the air out of Bambi just fine.

73 de KE4SKY In Home Mix We Trust From the Home of Ed's Red in "Almost Heaven" West Virginia

Attached Files

Lon posted this 12 December 2006

” I use ONE part of wheelweights to SEVEN parts of plumber's lead “ Mr. Harris, is this correct? I thought plumber's lead was about 50/50 lead/tin?

Attached Files

Idaho Sharpshooter posted this 14 December 2006

311284 from some salvaged linotype and lead 65/35% mix. About 2300fps from my Krag rifle, 130fps slower from the carbine. I shoot them in the ribs, usually breaks one going in, scrambles the heart and lungs, and goes out the other side. Never found one out of six mule deer, and two elk. 75 to nearly 200yds. It just kills them...

Rich DRSS NRA Life Member

Attached Files

454PB posted this 16 December 2006

Plumbers lead is usually considered “pure” lead.

Attached Files

Max Baglimit posted this 16 April 2007

In my .308 I use a 170 gn Lyman 311291 (75/25 - WW/Lino HT) propelled by 30 grains of IMR 3031. This gives me about 2000 fps with excellent accuracy. Does a number on hogs and deer. Just try and busted em through the shoulders.

Attached Files

CB posted this 27 November 2007

I am planning on Elk Hunting with a 300 Win Mag and using the Lyman 311284 bullet. Anyone had any experience with cast bullet in 300 win mag and how heavy a bullet would you use for Elk?

Jerry

Attached Files

Ed Harris posted this 27 November 2007

” I use ONE part of wheelweights to SEVEN parts of plumber's lead “

Mr. Harris, is this correct? I thought plumber's lead was about 50/50 lead/tin?"

The “plumber's lead” I am referring to is ordinary commercial 'pig' lead, which is nominally “pure” but not of nuclear reactor shielding or laboratory grade. Ordinary pig lead is generally about 5 BHN and usually contains no more than 1% total combined of other alloy content, which may include traces of antimony, tin and arsenic, with calcium, copper and zinc hopefully below the detection limit by xray diffraction.

"Plumber's solder” used to be 50-50 tin-lead, back in the days when water pipes were mostly lead. Since lead pipe and lead-bearing solders were banned by EPA for use in potable water supplies plumber's solder used these days for joining copper pipe is 95 percent tin and 5% antimony, usually found in one pound wire reels, rather than bars. You can still find bar solder used in wave soldering machines for electronic circuit boards, but it will be 63-37 to provide lowest melting point, minimum drossing and maximum fluidity, see

http://www.action-electronics.com/kester.htm>http://www.action-electronics.com/kester.htm

73 de KE4SKY In Home Mix We Trust From the Home of Ed's Red in "Almost Heaven" West Virginia

Attached Files

CB posted this 18 December 2007

I have a Spanish FR8 in 308 and it works great for hunting, I use a 200 gr cast RN GC bullet. It's a Lyman #311299 mold

The sights are a little on the basic side, but they work.

Merry Christmas,

Jerry

Attached Files

cbshtr posted this 26 December 2007

I used the Ideal 311413 for taking my last deer in 2002. I wrote an article about it (TFS Nov/Dec 2007) which describes what I did to it to make a pointed bullet into a flat point. The bullet performed very well with the deer going probably less that 25 yards. I just bought a Savage 10 Whitetail Hunter in 308 and once I get the barrel broke in I plan on working on target and hunting CB loads. Although the Ideal bullet did work well I'm going to try the SAECO 305 and RCBS 200 SIL. I believe the extra weight will help with penetration if the impact veleocity is down a little.

Robert Homan

Attached Files

44 Flattop posted this 31 March 2008

miestro_jerry wrote: I am planning on Elk Hunting with a 300 Win Mag and using the Lyman 311284 bullet. Anyone had any experience with cast bullet in 300 win mag and how heavy a bullet would you use for Elk?

Jerry

Did you get an elk with your .300?  I've taken a lot of elk with cast and I hesitate to say I wouldn't use a .30 caliber.  I use the RCBS 180 gr FN in the 30-06, .308 and .30-30 all moving along at around 1900fps and I wouldn't feel comfortable with even this bullet that weighs around 190grs for me.  For elk I draw the line at .348 and larger.  That sure doesn't mean you can't kill one with a .30 caliber :D  Shucks, I killed a small bull once with just a 4 3/4” .44 special using an RCBS 255 gr SWC at about 950fps with a single shot through the ribs at 40 yards! 

Back to the original subject, in the .30 caliber I use the RCBS 180gr exclusively.  3 parts WW's, 1 part pure lead.  1900fps is a good deer killing velocity out to about 150 yards or a little more.  I"ve taken quite a few deer with it and a few friends also who I provide the cast bullets for.  Not many have went more than just a few yards, all the time you can eat right up to the bullet hole.  I've been trying to think, but I can't remember a single time we ever recovered a single bullet.    Blood trails aren't quite as good as the larger calibers, 44 or 45, but it sure get the job done!

44

Attached Files

CB posted this 01 April 2008

44,

On many hunting trips that I have gone with, I have seen people use the 303 British round for moose. Several people have used medium caliber rounds in T/C Contenders. When out Grizzly hunting with a friend he was using a 7mm, but required many round to finish the bear off.

I do understand the idea of a bigger round, but I also remember that the U.S. Army went from a 30 06 to a 223 in about 25 years, with still a good kill ratio.

My 300 Mag is a 300 Remington Ultra Mag. I haven't found a lead bullet yet that I would use at the velocity this rifle can achieve, with a factory bullet of 200 gr you can push the bullet up to 3,000 FPS.

I shoot a 'yote with a 150 gr Ballistic tipped jacketed bullet, one of those super duper hunting bullet that can be pushed to 3.500 FPS in this rifle. I thought it would go thru the 'yote, it did sort of. Think about shooting a human being with 105mm Howitzer.

You would not believe the bruise that I got on my shoulder and the rifle has a factory installed sissy pade.

Ground Hog season is now upon us out here in Eastern Ohio, so I am thinking 35 Remington or 45-70 for the G Hogs. CBs of course. Or maybe I will just use my 10/22T instead.

Jerry

 

 

 

 

Attached Files

44 Flattop posted this 02 April 2008

miestro_jerry, I was just curious if you had taken an elk with a cast bullet out of your .300!  I don't doubt the capabilities of the various 300's and such on big game, I've killed a few elk with a .300 H&H and 7mm Rems using jacketed bullets.  I was most interested in the cast aspect of elk with your .300.

I shoot a 'yote with a 150 gr Ballistic tipped jacketed bullet, one of those super duper hunting bullet that can be pushed to 3.500 FPS in this rifle. I thought it would go thru the 'yote, it did sort of. Think about shooting a human being with 105mm Howitzer.

Now that would be COOL!  I oughta load some of those up in MY 300 H&H and smoke a few brush pups myself!

44

Attached Files

CB posted this 02 April 2008

44,

I am getting ready for next season. I am casting lino in to 200 gr bullets, then hardening them. Even then I may not be able to push them as fast the rifle is capable of. The CBs may break up in flight. I was thinking of a tall gas check with a soft CB for elk if the lino ones don't work that well.

 

Jerry

Attached Files

Scott Merchant posted this 02 April 2008

Jerry

I think Bullets cast of lino at the velocity you are trying to achieve will more then likely break up on impact. Trying to get cast bullets to work at jacketed velocity's in a 300 mag and perform well for hunting does not work in my experience. 44 Flattop recommendation of at least 35 calibre is good advice, and I would add use a flat point bullet of sufficient weight. Scott

Attached Files

CB posted this 02 April 2008

Scott,

I am currently experimenting with different type of casting, but you are right hard cast or lino bullets turn into frangible ammo.

 

Jerry

Attached Files

Lefty posted this 02 April 2008

Scott

Have you ever tried to make 30 cal hollow points using a drill press?  It seems like it should not be too difficult.  I was thinking of using a counter sink and just put a shallow cone shaped indentation in the nose.

Jim

Attached Files

jhalcott posted this 06 April 2008

I have used quite a few .30 molds for hunting deer and ground hogs. Most were in the 150 to 200 grain range. Velocity was almost always around 2200 fps. I have tried flat nosing the pointy and round nosed ones with a lot of success. I tried hollow pointing them with a drill press, but had much better results when I used a lathe to turn the bullets and kept the drill stationary in the tail stock. Accuracy was MUCH better and weight was held to a closer tolerance.The 31141 and 311291 are my favorites I guess, working in every thing from the 30 Herret to the 30-06.

Attached Files

Scott Merchant posted this 07 April 2008

Lefty

I have tried some in a Forster trimmer with a hollow point attachment, but they where never concentric so I gave up. I here Wilson makes a hollow point attachment for there trimmer, would work better I think.

Scott

Attached Files

sart256 posted this 17 September 2011

Ed, what is that bullet in the picture and is it still available? I have been trying the Ranch Dog 30 cal. TLC-31-165-RF in other than the 30-30. My mold drops them out at 312.5 andI size them down to 312 for 303 British. Good so far at the range can't wait for an OT in the field.

Attached Files

gnoahhh posted this 17 September 2011

I made the mistake once, many years ago, when inflicted with the hubris of youth, of using a 180 grain RN at around 1800fps, cast from linotype, on a small deer. Naturally the results were lackluster as it took multiple shots, from a single shot, to kill that poor creature. I learned my lesson that day and now use 190-210 grain .30 bullets with wide flat meplats at 10-13bhn, driven at .30/30 velocities and honestly can't tell the difference between them and factory .30/30 ammo.

Attached Files

6pt-sika posted this 17 September 2011

sart256 wrote:  I have been trying the Ranch Dog 30 cal. TLC-31-165-RF in other than the 30-30. My mold drops them out at 312.5 andI size them down to 312 for 303 British. Good so far at the range can't wait for an OT in the field. I fooled with the RD 311-165GC before RD made it available to the general public . I used it only in  Marlin 30-30's however . But in about 7 different rifles ballard and Micro I got very good results with 20-22 grains of XMP5744 . All my bullets were straight air cooled WW's and I also sized at .312” for my 30-30's . Those seven rifles were all shot on paper of course and most of them were used in lever action silhouette matches . So I can honestly say I tried this bullet out to 200 meters . I am sorry to say I used this bullet on only one whitetail and it did as expected . After the shot at 60 yards the deer didn't go any further then 15-20 yards .

Attached Files

rockquarry posted this 18 September 2011

I've killed small Texas whitetails with .30 caliber cast bullets, but learned a long time ago there are better choices for deer hunting. As has been mentioned before - use soft bullets driven fast and placed well. Limit shots to shorter distances than you would if using something more suitable. I'v had no experience hunting with hollow point bullets, but it seems these would be the best way to go.

Attached Files

sart256 posted this 18 September 2011

Ed, what bullet is this and is it still available?

Attached Files

6pt-sika posted this 18 September 2011

rockquarry wrote: I've killed small Texas whitetails with .30 caliber cast bullets, but learned a long time ago there are better choices for deer hunting.

WHile I don't disagree with that statement , it can be used with ANY cartridge bullet combintaion . There will ALWAYS be something better . And with that being said I've killed a number of Virginia deer with 30-30's , 32 Specials , 32-40's and 35 REM's using cast bullets . And they were all quite dead in a reasonable fashion .

I personally prefer the 444 and 45-70 with cast bullets but thats just something I arrived at more because I liked the available molds then any other reason .

Attached Files

6pt-sika posted this 19 September 2011

rockquarry wrote:  I'v had no experience hunting with hollow point bullets, but it seems these would be the best way to go.

I've used HP's in the 444 and 45-70 with good results on whitetails .

When I had all the 30-30's I had a factory Lyman 311041 HP mold . The bulet shot very well on paper but again I'm sorry to say I never tried this one on deer .

Attached Files

galenaholic posted this 19 September 2011

I've taken fifteen deer with the Lyman #311291 and two with the RCBS #30-180-FN over the years. It's ben a while as the 30-30 isn't the best choice for deer where I now live. All bullet were made from wheelweights with a bit of tin added. I'd guess BHN was probably 12 at the most. I always tried for solid chest shots and have never ecovered a bullet. Most deer were down withing 25 yards. The Lyman bullet was doing about 2000 FPS and the RCBS right at 1900, maybe 1950 FPS. The Lyman bullet weight right at 175 gr. and the RCBS at 189 gr. I also have two Lyman #31141/311041 molds and an NEI clone. I haven't been able to get any of those three to shoot worth spit in any 30 caliber from the 30-30 to the 30-06. :X I know qite a few have said it's a good bullet but it has not been good for me. Doesn't mean I'll quit messing with it. When I feel I need a good case of frustration, I'll run some and try them again. .> Paul B.

Attached Files

jhalcott posted this 20 September 2011

I did have some accuracy problems with the 311041 AND 311291 when I tried a graphited lube a few years ago. I played with Moly lube a bit also. The moly lube seemed to work BETTER with out any carrier, that is a simple coating of moly,NO LLA or other lube. I used some Teflon pipe tape on some with satisfying results too. The guns used included a 14” Contender and Win.94 and a bolt 30-30. Also a couple bolt action 30-06's. All the bullets were gas checked.

Attached Files

Close